|
Effective May 1, 2010
All new projects or work received after May 1, 2010 will be estimated and billed with these
price's. The currant lead
time for rifle work is 9 to 11 months. Call for small repairs / machining.
All prices are subject to change without notice. We have
no control if prices are increased to us.
MASTER CARD & VISA
The price page is broken up into sections.
The work in each section
is priced individually for just that particular service or part install.
If your project requires
more than 2 of the first 3 sections [ A - B - C ] please refer to the
rebuild or complete build section.
The amount of bench time
to fit & finish a project is more than doing partial or maintenance repair
work.
Single or double section
work will price out cheaper because of less man hours & supplies to
disassemble, reassemble, cosmetics, fit & function.
Sections:
A : Barrel work
B : Action work ( includes bolt work)
C : Stock work
D : Metal coatings
E : Die's & accessories
F : Rebuilds
G : Complete Builds
GTR: Supplies parts
Y: You supply parts
Section A: Barrel Work
A dummy round prepped to work in your action is needed to
cut your chamber for neck dia. and throat length. I custom cut your chamber so
the bullet is touching the lands when you close the bolt. Virgin brass is what I
want. I do not want fired formed brass, even on Improved chambering's. I'm using
the dummy round to get a loaded neck dia. and a datum measurement from the ojive
to case head for throating. Old brass from a large chamber will cause me & you
problems. I need the dummy round to slide in and out of the chamber freely to
properly get the datum length of the bullet touching the lands. A case that
hangs up on the body stopping short of touching the lands will cause a false
length to cut the throat to long. Extra work incurred because of not sending me
virgin brass will be billed to you.
Stripped action sent in to Chamber - Thread - Crown - a new barrel -
Engrave barrel (cal. & nk. dia.) - 320 ground finish - Colloidal
Graphite barrel - Grafoil 2 oz. bottle, does not include
barrel blank.
|
$339.00 |
|
Barreled action sent in to Chamber - Thread - Crown - a new
barrel - Engrave (cal. & nk. dia.) - 320 ground finish -
Colloidal Graphite barrel - Grafoil 2 oz. bottle, does not include
barrel blank.
|
$374.00 |
|
Assembled rifle sent in to Chamber - Thread - Crown - a new barrel -
Engrave (cal. & nk. dia.) - 320 ground finish - Colloidal Graphite
barrel - Grafoil 2 oz. bottle, does not include barrel blank.
|
$409.00 |
|
Index fluted barrel w/ rib up.
|
$40.00 |
|
Extractor cut in barrel tenon for actions with protruding extractors,
example: Winchester controlled feed.
|
$65.00 |
|
Muzzle brake installed; no indexing or contouring. (does not include
brake)
|
$75.00 |
|
Muzzle brake installed w/ indexing & or contouring (does not include
brake)
|
$110.00 |
|
Vais Muzzle Brake w/ install
|
$215.00 |
|
Thread protector
|
$40.00 |
|
Grafoil
|
$14.00 |
|
Satin bead finish on barrel
|
$25.00 |
|
Polished bright barrel finish per hr. (min. 1 hr)
|
$65.00 |
|
Epoxy New barrel to New barrel block
|
$150.00 |
|
|
Remove barrel from barrel block - Block clean-up - Epoxy new barrel
to barrel block |
$275.00 |
|
Rechamber for Ackley Improved on Barreled action sent in: Remove barrel,
Set up barrel in lathe, Set back (if barrel shank is long enough) to cut new
neck dia to you brass, Advance thread, Index barrel, Machine tenon,
Chamber forward to -0.004 headspace, Throat for your dummy round, Re-install
barrel.
|
$295.00 |
|
Section B: Action Work, includes bolt work.
Single point remachine action & bolt, Bush firing pin hole & turn pin, Lap
lugs. Minimum Recommended to actions.
|
$250.00 |
Accurize Remington style action: Single point remachine action & bolt,
Double sleeve bolt body, Bush firing pin hole & turn pin, Double pin
recoil lug, Open lug for larger tenon, Lap lugs, GTR Lite steel firing pin
& spring, GTR Recoil lug (choice of .200, .250 & .350)
Recommended to get the most consistent action.
|
$560.00 |
Rivet Remington extractor back in w/ rivet. (an add for the riveted
extractor bolts still out there that need machining)
|
$21.00 |
New Remington extractor & rivet w/ install. .223 Bolt face - .308
Bolt face - Magnum Bolt face
|
$29.00 $32.00
$33.00 |
Double pin recoil lug (an add to min. recommended)
|
$55.00 |
Open lug for larger tenon
|
$10.00 |
Open factory lug for larger tenon & surface grind (an add to min.
recommended)
|
$25.00 |
Sako extractor installed in Remington bolt, all sizes, bolt face staying
the same or changing. Parts & labor
|
$150.00 |
Silver braze new or old bolt handle on Remington bolt (need action to
time)
|
$110.00 |
Add single torx screw to bolt handle to give mechanical hold.
|
$35.00 |
Add two torx screw to bolt handle to give mechanical hold.
|
$55.00 |
Glue in single shot follower for Remington L or S action w/ GTR follower
|
$35.00 |
Accurize Winchester style action: Single point remachine action &.bolt,
Double sleeve bolt body, Bush firing pin hole & turn pin Open action
thread to 1.062 x 16 tpi, Lap lugs
Recommended to get the most consistent action
|
$450.00 |
Open Winchester style action thread to 1.062 x 16 tpi (an add to min.
recommenced)
|
$35.00 |
Double sleeve bolt body & bore action race way
|
$200.00 |
Thread bolt handle for after market bolt knobs, 5/16 x 24 tpi.
Remington
700 L/A, S/A, Model 7 right & left, 721 & 722 right, Bat Straight right
|
$68.00 |
Thread bolt handle for above mentioned & add 1 torx screw. This is a
biggie, you have more leverage to pry the handle off now with the
extended handle..
|
$95.00 |
Bush firing pin hole & turn pin w/ priority mail return shipping. 1-3 day
turn around.
|
$82.00 includes return shipping |
2 bolts, Bush firing pin hole & turn pin w/ priority mail return shipping.
|
$157.00 includes return shipping |
3 or more ship UPS, figured at time of shipping.
|
$75.00 each, plus shipping |
Adjust trigger with adjustment screws
|
$35.00 |
Polish sears and adjust trigger with adjustment screws
|
$45.00 |
Respring - Polish sears - adjust trigger with adjustment screws
|
$55.00 |
Section C: Stock Work
Epoxy pillar bed two screw barreled action rifle
|
$300.00 |
Epoxy pillar bed three screw barreled action rifle.
|
$325.00 |
Epoxy bed stocks w/ aluminum bedding block.
|
$200.00 |
Epoxy bed barrel block actions into stock.
|
$350.00 |
Open stock forend for larger barrel, starts @
|
$50.00 |
Inletting to fit action in to stock for ride height & or notching for bolt
release, handle, ect. per hr.
|
$65.00 |
Inlet flat top stock for your barreled action. Only done on stocks for
rifles I'm building & bedding, per hr.
|
$65.00 |
Section
D: Metal Coatings
Cera Coat complete rifle metal, one color
|
$295.00 |
K-G Kote complete rifle metal, one color
|
$275.00 |
K-G Kote barrel & lug.
|
$150.00 |
Section E: Die's &
accessories
Custom Seater die from Newlon or Wilson die blank
|
$125.00 |
Custom Neck die from Newlon or Wilson die blank
|
$125.00 |
Custom Neck or Seater die cut from you Newlon or Wilson die blank
|
$80.00 |
Custom Bore guide (only for barrels that I am chambering).
|
$45.00 |
Section
F: Rebuilds
Rebuild your Remington Rifle or like style
rifles w/ aluminum bedding block: Single point
remachine action & bolt, Double sleeve bolt body, Bush firing pin hole &
turn pin, Double pin recoil lug, Open lug for larger tenon, Lap lugs,
Polish sears & set trigger to a safe setting, Chamber - Thread - Crown
(includes wildcats) but don't guarantee wildcats to feed , Satin bead
finish barrel & lug, Epoxy bed barreled action, GTR lite steel firing pin
& spring, GTR S.S. recoil lug, your choice of .200, .250 & .350, Stainless
Steel Match barrel, up to 28" fl. to fit stock forend contour,
Grafoil
|
$1750.00 |
Adding to the above a fluted barrel with indexing flute.
|
$165.00 |
Adding to the above bedding a wood stock or aftermarket fiberglass
stock.
|
$100.00 |
Deduction for not Double sleeving bolt body.
|
-$200.00 |
Rebuild your Winchester push feed or like
style rifles w/ aluminum bedding block: Single point remachine action &
bolt, Double sleeve bolt, Bush firing pin, Chamber - Thread - Crown
(includes wildcats) but don't guarantee wildcats to feed, Polish sears &
Adjust trigger, Epoxy bed factory stock, Stainless steel barrel up
to 28" fl. to fit stock contour, Grafoil.
|
$1525.00 |
Addition for extractor cut in barrel tenon for Classic's Control round
feed.
|
$65.00 |
Addition for larger action tenon 1.062 x 16 tpi. (very highly recommended
for all calibers, a must for magnums)
|
$35.00 |
Adding to the above a fluted barrel with indexing flute.
|
$165.00 |
Adding to the above bedding a wood stock or aftermarket fiberglass
stock.
|
$100.00 |
Deduction for not Double sleeving bolt body.
|
-$200.00 |
Section
G: Complete Builds
GTR: Supplies parts
Y: You supply parts
|
